Dining Room window wall

     This project took awhile to complete for many reasons.  The first was that the area of shelving had to match the existing section that I had made two years before.  The second problem was fitting around a large window, a radiator and uneven walls.  Added was the angles necessitated by the design.  The two sides of the window were not the same and the shelves weren't cut at a 45.   However, in all the project turned out very well and provided plenty of storage space.  Now the window and the wall are a focal point in the room.

Here are some pictures showing the progress of work.

 

The pieces are all stained and on the rack.   Second begins the hard part, dealing with all the angles pieces.

 

 

Here begins fitting doors on the base cabinets.

 

 



Building the radiator cover was tricky because you have to be able to take it out
to service the radiator.  It also had to fit perfectly under the counter.  Grill work let air circulate.

 

Not all woodworking involves making furniture.  There are infinite projects that you can be invited to do if people know you are a woodworker.  This project comes from a friend who owns pizza shops.  He is making a 28 inch pie and, of course, needs super-sized peels for getting the pies out of the oven. 

These "paddles" have to taper toward the edges so they slip easily under the pie in the oven.  When I made the first one a few months ago, I hand planed the entire surface.  This time I used a sled for my planer which gave me most of the taper I needed before  the final glue-up.  This cut my hand work in half, but it still was a bit of a job.

The final piece was 26" by 54".

Here is another "common sense" tip, born from experience.  This refers to the table saw and is important to note when cutting without the guard.  I know you do sometimes. 

When you are through with the cut and the pieces are past the blade on the off feed table, don't lift them up and over the spinning blade, even if the saw is coasting to a stop.  If by chance you drop the piece and it hits the blade it can become a wicked projectile.  The smaller and thinner the piece the worse it can be.  The piece can spin and travel like a disc and travel in any direction high or low. 

This is another reason for using guides but I know that some procedures won't allow you to.  If this is just one cut I'm making, I'll turn the saw off and lower the blade before retrieving the pieces.  Then I can just slide the pieces off the table safely.

Sounds simple but you have to think about doing it each time and form the habit.  It only takes one miss or slip to create an accident.  And you can ruin a beautiful piece of material and lose all the work you spent making it.

This project was building a cabinet around a laundry sink.  The cabinet had to be matched with the existing cabinets, both style and color.  The consruction had to take into account the inside demensions to make the sink fit. 
A face frame has a false drawer front and a door on Euro hinges, giving access to bottom storage.

The sink was disconnected and I was able to remove the legs.  Then I  provided a platform for it inside the cabinet, leaving the bottom portion clear for storage.

The back was left  open for ease of replacing the plumbing.  A solid surface material is being used to frame the sink opening and will be attached to the top to provid a clean look that is easy to clean.  Here it is installed but without the top surface...... to be added later..........

Push stick tip #4

Building corner cabinets can be a nightmare especially when the angles are not 45.
I was trying to get corner shelves fit into this cabinet and forgot to allow for the 1/4 inch backs.  This led me to the problem of then cutting 1/4 inch off of each of the long sides on all the shelves.

To solve the problem and to keep all the good sides up I turned to my trusty push stick.  I always have a number of them with different thichness sides so I can rip narrow pieces.  This time the piece was only slightly over 1/8 inch.  The pusher that I made had 1/8 sides and so worked quite well in helping me with this task.

Take a look at how things worked out, in the video section.  The method takes careful technique.  If it doesn't feel right don't try it.  The pusher keeps the cutoff from flying up or back.

 

Here is an example of what homeowners can do to brighten a dull spot in their home. With a little help from EG Wood, this refrigerator corner is now useful and definitely brighter with the new lighting system. Here are before and after pictures.

 

 

 

     First the refrigerator was given a better home.  The exposed side was covered with nice harwood veneer to match the surrounding wood. 
     The top of the refrigerator is always a catch-all spot for "things" that can't be easily fetched unless husband gets a ladder.  So, a display shelf was the choice, created with added lighting to show off some better pieces of kitchen ware that may only be used occasionally. 
     The final step was to create a cabinet worthy of that corner.  Instead of a flimsy roll cart, a more permanent cabinet was made.  It has three functions now.  With a granite top it is part of the kitchen, a usable surface.  The doors and drawer are storage you can reach. The sides hold 20 bottles of wine.  You can use the entire cabinet for wine serving.  The granite top is unharmed by water, heat or alcohol.

Many of you woodworkers might have a workbench like mine.  My end vise has a single screw and rides on two pipe pieces.  It is a simple mechanism but when clamping anything on the corner of the vise the jaws won't remain parallel.  This idea came to me to help keep the jaws aligned when I'm using just the corner of the vise.

I made a stack of 1/4 x 2 x 3 inch pieces and used a carraige bolt and wing nut to secure them.  I then put the number of blocks in the opposite end of the vise that matches the thickness of the board I'm trying to clamp. 

  

 

Now the jaws of the vise are parallel and will hold the work solidly.

  



 

This is a creative idea for a wood push stick.  Take a wooden coat hanger and cut it in half and presto! you have two of them for price of one.  I've seen this type of stick being used to pull out oven trays, only only with a hook on the end instead of a notch.

This is a simple trick.  Anything to save your fingers.  Always use a solid push stick when working close to the blade.

Project, Torsion Box.....

The torsion box is a handy way to create a thick panel with the strength to span a large area.  Because the panel is mostly hollow, it also is very light.  It can also maintain its flatness and not flex under stress. 

The secret is in the core.  Everyone has seen the concept in the making of hollow core doors. The core is mostly made with cardboard and the doors don't really have to lay horizontally and support a lot of weight.  However, if you want to make a table or roof where strength is an issue, then try this idea and make a torsion box of your own.

The system requires three components, a core grid with a layer on top and a layer on the bottom.  Sounds simple and is.  In this project I used 1/2 in plywood for the grid with 1/4 ply for the top and bottom layers.  In the choice of materials, the factors of strength, length and lightness dictate. 

Make the grid by cutting long strips and then filling in the cross pieces with short cut-offs, or make continuous crossing strips and notch them to fit together, finger joint style.  Smaller grids make the panel heavier and larger grids are more open and make  a lighter panel.  Make the outside pieces of the whole frame, out of thicker material. 

 

The flat spots are where table legs will be added.

 

This torsion box, covered with stainless, makes a generous work station.

 

The central horizontal has to span a five foot wide TV and support the top cabinets.

 

 

Work on a solid, flat surface to attach the top with glue and screws. This will be the underside that won't be seen.  Using weight, (cement blocks, etc....) make sure of the flatness and let the glue dry.  Turn the whole thing over and add the bottom layer with glue and add weight to the top instead of screws.  Let the glue dry, sand the edges or add trim and you have a great table or whatever other use you have devised.

The two projects I've shown here are first a bakery table covered with stainless steel and secondly a cabinet for a huge TV.  Both utilize a torsion box for horizontal strength.

Push-stick tip #3

You can use this handy  push stick to quickly cut yards of moldings for any project.  First determine the lengths you need then cut wide pieces that you will need to cut strips from.  Take the wide pieces and rout or shape the molding contour on one or both edges.   Then with your handy dandy push stick you can safely cut off strips of molding as fast as you can rout them without having to change the table saw fence setting.

Some styles of moldings are round or irregular and the pusher might not make good contact.   The tip here is to take off the side of the push stick and make one thaat is thicker or thinner or just makes better contact.   Safety here comes at the end of the cut when the tendency is for the cut piece to twist or turn.  Good contact all through the cut is imperative.  It's worth the time it takes to do this for safety.  The idea that "I'm only going to make one or two pieces" can be the dangerous concept.

Super-safe table saw push stick #2

Super-safe table saw push stick #2

This push stick for the table saw is great because it prevents you from getting involved with the blade.  It is shown here being used with a newer saw with a wider fence.  As you can see all you need do is adjust the width to the dimensions of your particular fence.

The three different size side walls allow you to cut very thin strips.  You can use the pusher with the new guards and splitters in place for wider pieces.  The blade cover does prohibit cutting very thin slices.

Super-safe push stick for older table saws.

Super-safe table saw push stick.  #1

I am posting this idea for the sake of safety.  Many old table saws are still in use in cabinet shops today.  Being vintage, they don't come equipped with the newest safety features like riving knives and spreaders that prevent kick-back.  Also they lack the over the blade covers that keep your hands away from the blade.  Not everyone can or wants to upgrade their table saw's safety equipment, or buy a new saw.

I have come across a very simple idea to protect your fingers and maintain control in nearly all ripping operations on your table saw.  This push stick stradles the fence with a handle on top for control.  When you push a piece through the blade you have complete control and can't get close with your fingers.  Every saw owner can make one, even if you do have the latest model.

I have seen some woodworkers, trusting their experience, using their thumb to guide stock between the blade and the fence.  Some will hook their little finger over the fence
for better control.  This does improve your chances but  I don't want to take any chances!  I want to lower my odds of losing a finger to zero!  Have a look....

This simple "duck" push stick is like a seat belt, in that you will get used to using it.  It becomes second nature, a habit.  If anytime, this stick hits the blade you can replace it with a bright shiny new one and still order four beers with one hand.